Page 461 - ISCAR(HOLE_MAKING_CATALOG_65)

60°
TCMT-SM 91 º 91 º 95 º
Triangular Inserts with a 7° 91 º
Positive Flank for Semi-Finishing L
and Finish Turning on Soft D1 ITS BORE
Materials and Exotic Alloys RE 7°
IC S

Dimensions Tough 1 Hard Recommended
Machining Data

IC830 IC8350 IC8250 IC908 IC8150 IC5010 IC428 IC5005 IC807 IC907 ap f
Designation L IC S RE D1 (mm) (mm/rev)
TCMT 110204-SM 11.00 6.35 2.38 0.40 2.80 • • • • • • • • 0.20-3.00 0.05-0.25
TCMT 110208-SM 11.00 6.35 2.38 0.80 2.80 • • • 0.50-2.50 0.07-0.25
TCMT 16T304-SM 16.50 9.52 3.97 0.40 4.40 • • • • • • • 0.50-3.00 0.06-0.25
TCMT 16T308-SM 16.50 9.52 3.97 0.80 4.40 • • • • • • 0.50-3.00 0.08-0.28
TCMT 16T308-SM* 16.50 9.52 3.97 0.80 4.40 • 0.50-3.00 0.08-0.28
For tools, see page: IHBR (409)

80°

WCGT 93º
Trigon Inserts with a 7° L
Positive Flank and Chipformer
for Finish Turning 7°
RE
IC S

Dimensions Tough 1 Hard Recommended Machining Data

IC908 IC30N ap f
Designation L IC S RE (mm) (mm/rev)
WCGT 020102L 2.18 3.97 1.59 0.20 • • 0.40-2.00 0.05-0.10
WCGT 020104L 2.18 3.97 1.59 0.40 • • 0.40-2.00 0.10-0.15
For tools, see pages: IHAXF (432) • IHAXF-AVI (434) • IHAXF-E (434) • IHWF (436)

60°

TPGX 91 º
Triangular Inserts with an 11°
Positive Flank and Ground L
Chipformer for Finish Turning D1
11°
RE
IC S
Recommended
Dimensions Tough 1 Hard Machining Data

IC908 IC20 IC20N IC520N ap f
Designation L IC S RE D1 (mm) (mm/rev)
TPGX 090202-L 9.52 5.56 2.38 0.20 3.00 • • • • 1.00-2.00 0.10-0.20
TPGX 090204-L 9.52 5.56 2.38 0.40 3.00 • • • • 1.00-2.50 0.15-0.20
TPGX 110302-L 11.00 6.35 3.18 0.20 3.50 • • • • 1.00-2.50 0.10-0.20
TPGX 110304-L 11.00 6.35 3.18 0.40 3.50 • • • • 1.00-3.00 0.15-0.20
TPGX 110308-L 11.00 6.35 3.18 0.80 3.50 • 1.00-3.50 0.15-0.25
For tools, see pages: IHAXF (432) • IHAXF-AVI (434) • IHAXF-E (434) • IHFF (436) • IHFF-C (413)

459