Page 562 - ISCAR(TURNING-CATALOG-42-2022)

FACE GROOVING HFHR/L-5T CW 10.00 20.0 20.0 20.0 CDX HFHR/L --5T10 21.00 HF CW 25.0 LH OAL 30.0 (2) 38.0 OAH OAH HBH SR M6X16 DIN912 HW 5.0

Integral Holders for Facing
H
CDX
HBH
WF2

DAXN-DAXX
B
WF
Right-hand shown
(1)
B
LH
CDX
WF
HF
H
OAL
Designation
WF2
DAXX
DAXN
HFHR/L 20-25-5T10
28.0
7.1
140.00
-
5.00
HFHR/L 25-25-5T10
30.0
5.00
10.00
150.00
7.1
26.00
25.0
25.0
25.0
25.0
-
SR M6X16 DIN912
HW 5.0
33.0
38.0
HFHR/L 25-110-5T14
33.0
25.0
HFHR/L 25-52-5T14
SR M6X16 DIN912
150.00
25.0
25.0
52.0
HW 5.0
32.5
23.50
5.00
14.00
75.0
5.00
150.00
HFHR/L 25-75-5T14
110.0
25.0
32.5
25.0
SR M6X16 DIN912
14.00
HW 5.0
75.0
23.50
25.0
33.0
SR M6X16 DIN912
HW 5.0
140.00
21.00
28.0
31.0
17.00
5.00
34.0
20.0
20.0
HFHR/L 20-28-5T15
30.0
20.0
35.0
HW 5.0
34.0
30.0
31.0
SR M6X16 DIN912
17.00
20.0
HFHR/L 20-31-5T15 5.00 14.00 25.0 25.0 25.0 150.00 - - - - - 23.50 110.0 200.0 32.5 33.0 - - - - - SR M6X16 DIN912 HW 5.0
5.00
140.00
21.00
20.0
20.0
HFHR/L 25-28-5T15 5.00 17.00 25.0 25.0 25.0 150.00 - 26.00 28.0 31.0 34.0 35.0 - SR M6X16 DIN912 HW 5.0
HFHR/L 25-31-5T15 5.00 17.00 25.0 25.0 25.0 150.00 - 26.00 31.0 35.0 34.0 35.0 - SR M6X16 DIN912 HW 5.0
HFHR/L 20-35-5T20 5.00 20.00 20.0 20.0 20.0 140.00 - 21.00 35.0 40.0 39.0 31.0 - SR M6X16 DIN912 HW 5.0
HFHR/L 20-40-5T20 5.00 20.00 20.0 20.0 20.0 140.00 - 21.00 40.0 45.0 39.0 31.0 - SR M6X16 DIN912 HW 5.0
HFHL 25-200-5T20 5.00 20.00 25.0 25.0 25.0 150.00 - 23.50 200.0 800.0 32.5 33.0 - SR M6X16 DIN912 HW 5.0
HFHR/L 25-35-5T20 5.00 20.00 25.0 25.0 25.0 150.00 - 26.00 35.0 40.0 39.0 36.0 - SR M6X16 DIN912 HW 5.0
HFHL 25-40-5T20 5.00 20.00 25.0 25.0 25.0 140.00 - 26.00 40.0 45.0 39.0 36.0 - SR M6X16 DIN912 HW 5.0
HFHR 25-200-5T20 5.00 20.00 25.0 25.0 25.0 150.00 - 26.00 200.0 800.0 32.5 33.0 -
HFHR 25-40-5T20 5.00 20.00 25.0 25.0 25.0 150.00 - 26.00 40.0 45.0 39.0 36.0 -
HFHR/L 20-45-5T25 5.00 25.00 20.0 20.0 20.0 140.00 - 21.00 45.0 55.0 44.0 32.0 - SR M6X16 DIN912 HW 5.0
HFHR/L 20-55-5T25 5.00 25.00 20.0 20.0 20.0 140.00 - 21.00 55.0 70.0 44.0 35.0 3.0 SR M6X16 DIN912 HW 5.0
HFHR/L 25-45-5T25 5.00 25.00 25.0 25.0 25.0 150.00 - 26.00 45.0 55.0 44.0 37.0 - SR M6X16 DIN912 HW 5.0
HFHR/L 25-55-5T25 5.00 25.00 25.0 25.0 25.0 150.00 - 26.00 55.0 70.0 44.0 37.0 - SR M6X16 DIN912 HW 5.0
HFHR/L 20-70-5T28 5.00 28.00 20.0 20.0 20.0 140.00 - 21.00 70.0 95.0 47.0 35.0 3.0 SR M6X16 DIN912 HW 5.0
HFHR/L 25-130-5T32 5.00 32.00 25.0 25.0 25.0 150.00 - 26.00 130.0 180.0 51.0 37.0 - SR M6X16 DIN912 HW 5.0
HFHR/L 25-180-5T32 5.00 32.00 25.0 25.0 25.0 150.00 - 26.00 180.0 800.0 51.0 37.0 - SR M6X16 DIN912 HW 5.0
HFHR/L 25-70-5T32 5.00 32.00 25.0 25.0 25.0 150.00 - 26.00 70.0 95.0 51.0 37.0 - SR M6X16 DIN912 HW 5.0
HFHR/L 25-95-5T32 5.00 32.00 25.0 25.0 25.0 150.00 - 26.00 95.0 130.0 51.0 37.0 - SR M6X16 DIN912 HW 5.0
• DGN & GRIP 5.. inserts can be used only with right-hand tools, HGPL 5.. inserts with left-hand tools • For user guide, see pages 604-613
(1) Minimum penetration diameter
(2) Maximum penetration diameter
For inserts, see pages: HFPR/L (576) • HFPR/L (full radius) (576) • GRIP (269) • GRIP (full radius) (270) • DGN/DGNC/DGNM-C (481)
• DGN/DGNM-J/JS/JT (483) • DGN-W (482) • HGPL (578)
No limitation for widening groove toward or away from center, except for the following tools:
HFHR/L- o -31-5T15 HFHR/L- o -30-6T10 HFHR/L-o-25-5T10 HFHR/L- o -28-5T15 d
D d D d D d D d Limitation of widening
31 15 30 7 25 4 28 13 toward center (d)
32 10 31 4 26 1 29 8 depends on the major
33 7 32 1 ≥27 0 30 5 diameter (D) as per D
34 4 ≥33 0 31 3 chart
35 2 32 1
≥36 0 ≥33 0

560 ISCAR